could result. 0 For DC powered systems, use Aiphone power supply model specified with . A Even if two GH-VBC units are used as extension adaptors. Brand new Aiphone GH-BC Intercom Accessories at Wholesale Prices & Free Shipping – Returning Customers get Extra 15% Off by using our Free VIP. GH-BC AIPHONE BUSS CONTROL. Model. Category: Accessories. Description; Reviews (0). Product Description. Audio bus control unit for GH system.
|Published (Last):||23 August 2007|
|PDF File Size:||14.17 Mb|
|ePub File Size:||15.69 Mb|
|Price:||Free* [*Free Regsitration Required]|
The unit must be installed and wired by a qualified technician. Use any long thin tool, such as a fine screwdriver. Or point us to the URL where the manual is located.
Ae 1-2, Ae a e, Bc d – Aiphone GH SERIES 0207 AIC User Manual
Mount the station unit to the mounting bracket. Set access codeEnter new 4-digit Access Code.
Entrance monitoring is possible for only oneresidential station at a time. Plug in the ribbon cables between modules in a daisy-chained manner. The ID code will be reset to the default setting of ” “.
Aiphone GH-BC Two-Wire Bus Control Unit For GH
When units do not operate normally, request repairs from a qualified technician. Press the light button once while in communication.
Skipped at time of entrance station monitoring. Use any long thin tool, such asa fine screwdriver.
Aiphone GH-BC Manuals
To remove the terminal block, slide the terminal block and pull it out. The doorbell button is pushed. Surface-mount box GFB c. Do not install the entrance station in aplace where there would be a brightlight behind a visitor or where therewould be a bright background or in aplace where the camera lens would bedirectly exposed to sunlight or a brightlight.
Aiphone GH-BC Audio Bus Control Unit for GH System, 1 per standard system (GHBC GH Bc)
Connect the wiring to the terminal block. Apar tment Inter com System. When the system includes GHNS, program the resident information names and roomnumbers in advance. There are three different types of call tones: The door release function will activate on the entrance stationthat is in communication. Do not install the entrance station in a place where there would be a bright light behind a visitor or where there would be a bright background or in a place where the camera lens would be directly exposed to sunlight or a bright light.
Set the system to program mode. Residential station For details, see You will hear a low-volume call tone.
To position the speech module in the center row, run GF-C through the joint pipe in advance. Connect the wiring to the terminal block. This equipment generates, uses, and can radiate radiofrequency energy, and if not installed and used in accordance with theinstructions, may cause harmful interference to radio communications. Activates while the button is pressed.
Example of interconnection of modules. If installing a digital entry system, the program for loading names and numbers for each tenant is also located on the CD.
You will hear a low-volume call tonefrom the entrance station. A call tone sounds as long as thebutton is held down. For information on how to use the setup tool, see the text.
You will hear a low-volume call tone from the entrancestation. Monday – Friday PH: Put back the terminal cover. Mount the mounting bracket on the 1-gang box. If the programming was unsuccessful, an alarm sound will be emitted.
You can change the “Welcome” text. It’s a community-based project which helps to repair anything. Page 39 Door Release1. Page 9 Expanded System Configuration Diagram1. Station-to-station wiring For details, see d. While using the mounting gauge to makeadjustments, tighten the screws. For details, see 2. For details, see above. A continuous beep will be emitted to verify the communication link has been cleared.
The outside light of the entrance will turn on for the presetduration of time. Enter room s using 1 to 6-digit characters. Sub trunk line 1 – 4Sub aiphonr line 2 – 4 are the same as 1. Set up the modules. Enter resident name up to 16 characters.